首页期刊简介编委会在线投稿 投稿指南投稿模板学术道德规范申明约稿简则本刊声明 期刊浏览往期浏览知网万方维普 公告通知防止假冒网站声明学术道德规范声明联系我们English
文章摘要
铂镓合金板材焊接接头组织与力学性能研究
Study on microstructure and mechanical properties of welded joint of Pt-Ga alloy sheet
投稿时间：2024-04-28
DOI：
中文关键词: 金属材料 铂镓合金 激光焊 氩弧焊 抗拉强度
英文关键词: metal material platinum-gallium alloy laser welding argon arc welding tensile strength
基金项目:
作者单位王浩 河海大学 材料科学与工程学院，南京 211100英特派铂业股份有限公司，江苏 无锡 214194 尹俊 英特派铂业股份有限公司，江苏 无锡 214194 刘高斯 英特派铂业股份有限公司，江苏 无锡 214194 周泽华 河海大学 材料科学与工程学院，南京 211100 金英杰 英特派铂业股份有限公司，江苏 无锡 214194 杨志先 英特派铂业股份有限公司，江苏 无锡 214194
摘要点击次数: 1081
全文下载次数: 454
中文摘要:
探索及分析铂镓合金板材的焊接工艺，旨在为铂镓合金催化网的焊接提供理论基础。试验制备了Pt-2Ga、Pt-3Ga-2Ru与Pt-5Ga的1 mm厚度板材，采用氩弧焊与不同功率的激光焊对合金进行焊接，对其焊接后的拉伸性能、断口形貌、热影响区宽度、焊接区域的微观组织以及焊接区域元素成分的偏析程度等进行研究。结果表明，Pt-5Ga合金脆性较大无法满足催化网制备条件，Pt-3Ga-2Ru合金的焊接性能优于Pt-2Ga合金，同时晶粒尺寸有大幅减小的趋势。激光焊焊接件的焊接性能优于氩弧焊焊接件，热影响区的宽度更窄，元素的偏析程度也有所减小。将不同功率下的激光焊接试样进行对比后发现:焊接功率设定在350 W时对Pt-3Ga-2Ru合金的拉伸性能最好。
英文摘要:
The welding process of platinum-gallium alloy sheet is explored and analyzed in order to provide a theoretical basis for the welding of platinum-gallium alloy catalytic mesh. The 1 mm thick plates of Pt-2Ga, Pt-3Ga-2Ru and Pt-5Ga were prepared. The alloys were welded by argon arc welding and laser welding with different powers. The tensile properties, fracture morphology, heat affected zone width, microstructure of the welding area and the segregation degree of element composition in the welding area were studied. The results show that the brittleness of Pt-5Ga alloy is too large to meet the preparation conditions of catalytic network. The welding performance of Pt-3Ga-2Ru alloy is better than that of Pt-2Ga alloy, and the grain size has a tendency to decrease greatly. The welding performance of laser welding parts is better than that of argon arc welding parts, the width of heat affected zone is narrower, and the degree of element segregation is also reduced. After comparing the laser welding samples at different powers, it was found that the tensile properties of Pt-3Ga-2Ru alloy were the best when the welding power was set at 350 W.
查看全文
查看/发表评论 下载PDF阅读器
关闭
版权所有： 贵金属编辑部本平台为互联网非涉密平台，严禁处理、传输国家秘密
技术支持：北京勤云科技发展有限公司
滇公网安备 53019002000213号